Question 1

Should the backing strip be left on the finished weld or removed following welding? How is that indicated?

Accepted Answer

The backing may be either left on the fi...

Question 2

The purpose of a(n) ____________________ is to join parts together so that the stresses are distributed.

Accepted Answer

The answer of The purpose of a(n) ____________________ is to...

Question 3

In the ____ position, the pipe is vertical to the horizon and the weld is made horizontally around the pipe.

Accepted Answer

A)   horizontal rolled 1G
B)   horizontal fixed 5G
C)   vertical 2G
D)   inclined 6GE) None of the above
F) B) and C)

Question 4

On larger welding jobs, who usually determines the best type of joint to be used?

Accepted Answer

A)   Welder
B)   Welding engineer
C)   CAD artist
D)   CustomerE) A) and B)
F) All of the above

Question 5

Which of the following is not a classification of a type of weld?

Accepted Answer

A)   Surface
B)   Plug
C)   Face
D)   SeamE) A) and D)
F) A) and C)

Question 6

What does the term faying surface relate to?

Accepted Answer

A)   The surface of a joint that will be melted during the weld.
B)   The frayed edges of welder's pants, shirt, or other clothing.
C)   The surface that cannot be seen directly such as the inside of a pipe weld joint.
D)   It is the outside of the pipe or sides of a weld joint that have been cleaned for welding.E) None of the above
F) C) and D)

Question 7

____________________ are a shorthand language for the welder.

Accepted Answer

The answer of ____________________ are a shorthand language for the...

Question 8

In a(n)  ____ joint the edges of the metal meet so that the thickness of the joint is approximately equal to the thickness of the metal.

Accepted Answer

A)   tee
B)   lap
C)   butt
D)   outside cornerE) A) and D)
F) A) and C)

Question 9

It is easier for a crack to propagate through a continuous weld than it is on an ____________________ weld where it has to restart at the beginning of each weld.

Accepted Answer

The answer of It is easier for a crack to...

Question 10

Holes in the arrow side member of a joint for plug welding are indicated by placing the weld symbol ____ the reference line.

Accepted Answer

A)   next to
B)   above and below
C)   below
D)   aboveE) All of the above
F) B) and C)

Question 11

List the reasons for preparing the faying surfaces for welding.

Accepted Answer

Reasons for preparing the faying surface...

Question 12

In the ____ position, the pipe is fixed in a 45 degree inclined angle, and the weld is made around the pipe.

Accepted Answer

A)   inclined with a restriction ring 6GR
B)   horizontal fixed 5G
C)   vertical 2G
D)   inclined 6GE) None of the above
F) B) and D)

Question 13

On thin sections it is often possible to make full penetration welds using a(n)  ____ joint.

Accepted Answer

A)   square butt
B)   lap
C)   tee
D)   outside cornerE) All of the above
F) None of the above

Question 14

____________________ joints are usually welded on only one side.

Accepted Answer

The answer of ____________________ joints are usually welded on only...

Question 15

The size of the root face is important to ensure good ____________________.

Accepted Answer

The answer of The size of the root face is...

Question 16

In a(n)  ____ joint the edges of the metal overlap so the thickness of the joint is approximately equal to the combined thickness of both pieces of metal.

Accepted Answer

A)   tee
B)   lap
C)   outside corner
D)   edgeE) None of the above
F) B) and D)

Question 17

Which type of weld joint can be fitted together so that the joint forms a V-groove or square butt joint?

Accepted Answer

A)   Butt
B)   Tee
C)   Outside corner
D)   EdgeE) B) and C)
F) C) and D)

Question 18

In a(n)  ____ joint the edges of the metal are brought together at an angle, usually around 90 degrees to each other.

Accepted Answer

A)   butt
B)   tee
C)   outside corner
D)   edgeE) None of the above
F) All of the above

Question 19

Describe the four basic plate welding positions for grooves and fillet welds.

Accepted Answer

The American Welding Society has divided...

Question 20

A(n) ____________________ is designated by a right triangle.

Accepted Answer

The answer of A(n) ____________________ is designated by a right...

Exam 22: Welding Joint Design and Welding Symbols

List the reasons for preparing the faying surfaces for welding.

Correct AnswerverifiedReasons for preparing the faying surface...View AnswerShow Answer

A(n) ____________________ is designated by a right triangle.

Correct AnswerverifiedShow Answer

It is easier for a crack to propagate through a continuous weld than it is on an ____________________ weld where it has to restart at the beginning of each weld.

Correct AnswerverifiedShow Answer

What does the term faying surface relate to?

Correct AnswerverifiedShow Answer

Describe the four basic plate welding positions for grooves and fillet welds.

Correct AnswerverifiedThe American Welding Society has divided...View AnswerShow Answer

The size of the root face is important to ensure good ____________________.

Correct AnswerverifiedShow Answer

Which of the following is not a classification of a type of weld?

Correct AnswerverifiedShow Answer

In a(n) ____ joint the edges of the metal are brought together at an angle, usually around 90 degrees to each other.

Correct AnswerverifiedShow Answer

In the ____ position, the pipe is vertical to the horizon and the weld is made horizontally around the pipe.

Correct AnswerverifiedShow Answer

Should the backing strip be left on the finished weld or removed following welding? How is that indicated?

Correct AnswerverifiedThe backing may be either left on the fi...View AnswerShow Answer

In a(n) ____ joint the edges of the metal meet so that the thickness of the joint is approximately equal to the thickness of the metal.

Correct AnswerverifiedShow Answer

____________________ are a shorthand language for the welder.

Correct AnswerverifiedShow Answer

The purpose of a(n) ____________________ is to join parts together so that the stresses are distributed.

Correct AnswerverifiedShow Answer

Which type of weld joint can be fitted together so that the joint forms a V-groove or square butt joint?

Correct AnswerverifiedShow Answer

On larger welding jobs, who usually determines the best type of joint to be used?

Correct AnswerverifiedShow Answer

Holes in the arrow side member of a joint for plug welding are indicated by placing the weld symbol ____ the reference line.

Correct AnswerverifiedShow Answer

In a(n) ____ joint the edges of the metal overlap so the thickness of the joint is approximately equal to the combined thickness of both pieces of metal.

Correct AnswerverifiedShow Answer

On thin sections it is often possible to make full penetration welds using a(n) ____ joint.

Correct AnswerverifiedShow Answer

____________________ joints are usually welded on only one side.

Correct AnswerverifiedShow Answer

In the ____ position, the pipe is fixed in a 45 degree inclined angle, and the weld is made around the pipe.

Correct AnswerverifiedShow Answer

Correct Answer
verified
Reasons for preparing the faying surface...
View Answer

Correct Answer
verified

Correct Answer
verified

Correct Answer
verified

Correct Answer
verified
The American Welding Society has divided...
View Answer

Correct Answer
verified

Correct Answer
verified

Correct Answer
verified

Correct Answer
verified

Correct Answer
verified
The backing may be either left on the fi...
View Answer

Correct Answer
verified

Correct Answer
verified

Correct Answer
verified

Correct Answer
verified

Correct Answer
verified

Correct Answer
verified

Correct Answer
verified

Correct Answer
verified

Correct Answer
verified

Correct Answer
verified